View NLX2G66FCTAG_9028759.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? semiconductor components industries, llc, 2016 may, 2016 ? rev. 5 1 publication order number: nlx2g66/d nlx2g66 dual bilateral analog switch / digital multiplexer the nlx2g66 is a dual single pole, single throw (spst) analog switch / digital multiplexer. this single supply voltage ic is designed with a sub?micron cmos technology to provide low propagation delays (t pd ) and on resistance (r on ), while maintaining low power dissipation. this bi?lateral switch can be used with either analog or digital signals that may vary across the full power supply range from v cc to gnd. features ? wide v cc operating range: 1.65 v to 5.5 v ? ovt up to +5.5 v for control pin ? r on : typically 5.5 at v cc = 4.5 v and i s = 32 ma ? rail?to?rail input/output ? high on?off output voltage ratio ? high degree of linearity ? ultra?small pb?free, halide?free, rohs?compliant packages ? esd performance: > 5000 v hbm, > 400 v mm typical applications ? cell phones, pdas, mp3 and other portable media players 1b 1a 1c 2b 2a 2c figure 1. analog symbol pin assignments udfn8 wlcsp8 description 1 a1 1a 2 b1 1b 3 c1 2c 4 d1 gnd 5 d2 2a 6 c2 2b 7 b2 1c 8 a2 v cc this document contains information on some products that are still under development. on semiconductor reserves the right to change or discontinue these products without notice. www. onsemi.com see detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. ordering information marking diagrams xx = specific device code m = date code = pb?free package udfn8 mu suffix case 517bz udfn8 mu suffix case 517ca xxm 1 xxm 1 pin assignments udfn8 (top view) v cc 1c 2b 2a 1 1a 1b 2c gnd control input (c) switch f unction table l off hon 1 8 1 8 1 8 wlcsp8 fc suffix case 567mr xxxx ayww a = assembly location y = year ww = work week 2 3 4 8 7 6 5 wlcsp8 v cc 1c 2b 2a d1 1a 1b 2c gnd c1 b1 a1 d2 c2 b2 a2 (bottom view)
nlx2g66 www. onsemi.com 2 table 1. maximum ratings symbol rating value unit v cc positive dc supply voltage ?0.5 to +7.0 v v s switch input / output voltage (pins 1a, 1b, 2a and 2b) ?0.5 to + v cc + 0.5 v v i digital control input voltage (pins 1c and 2c) ?0.5 to +7.0 v i ok i/o port diode current 50 ma i ik control input diode current ?50 ma i i/o continuous dc current through analog switch 100 ma i l latch?up current, (above v cc and below gnd at 125 c) 100 ma t s storage temperature ?65 to +150 c v esd esd withstand voltage: human body model (hbm) machine model (mm) 5000 > 400 v stresses exceeding those listed in the maximum ratings table may damage the device. if any of these limits are exceeded, device function ality should not be assumed, damage may occur and reliability may be affected. table 2. recommended operating conditions symbol parameter min max unit v cc positive dc supply voltage 1.65 5.5 v v s switch input / output voltage (pins 1a, 2a, 1b and 2b) gnd v cc v v i digital control input voltage (pins 1c and 2c) gnd 5.5 v t a operating temperature range ?55 +125 c t r , t f input transition rise or fall time (on/off control input) v cc = < 3.0 v 0 20 ns/v v cc = 3.0 v 0 10 table 3. electrical characteristics symbo l parameter condition v cc guaranteed limit unit 25 c ?55 to 125 c min max min max v ih high?level input voltage, control input 1.65 to 1.95 v cc x 0.65 v 2.3 to 5.5 v cc x 0.7 v il low?level input voltage, control input 1.65 to 1.95 v cc x 0.35 v 2.3 to 5.5 v cc x 0.30 i i input leakage current, control input v i = v cc or gnd 5.5 0.1 1 a i s(on) on?state switch leakage current v is = v cc or gnd, v i = v ih , v os = open 5.5 0.1 1 a i s(off) off?state switch leakage current v is = v cc and v os = gnd, or v is = gnd and v os = v cc gnd, v i = v il , 5.5 0.1 1 a i cc quiescent supply current v i = v cc or gnd 5.5 1.0 10 a i cc supply current change v i = v cc ? 0.6 5.5 500 a c i control input capacitance 5 3.0 pf c i/o(off) switch off input / output capacitance see figure 3 5 6.0 pf c i/o(on) switch on input / output capacitance see figure 4 5 13 pf
nlx2g66 www. onsemi.com 3 table 4. switching characteristics symbol parameter condition v cc guaranteed limit unit ?55 to 125 c min max t plh , t phl propagation delay, a to b, b to a c l = 30 pf, r l = 1 k 1.8 6.5 ns 2.5 3.3 c l = 50 pf, r l = 500 3.3 2.5 5.0 2.2 t en (t pzl , t pzh ) enable time, c to analog output (a or b) c l = 50 pf, r l = 500 see figure 6 1.8 10 ns 2.5 6.5 3.3 5.5 5.0 4.9 t dis (t plzl , t phz ) disable time, c to analog output (a or b) c l = 50 pf, r l = 500 see figure 6 1.8 9.0 ns 2.5 7.2 3.3 6.5 5.0 6.0 table 5. analog switch characteristics symbol parameter conditions v cc 25 c ?55 to 125 c unit typ min max r on on?resistance v is = v cc or gnd, v i = v ih , see figure 2 i s = 4 ma 1.65 12 30 i s = 8 ma 2.3 9 20 i s = 24 ma 3.0 7.5 15 i s = 32 ma 4.5 5.5 13 r on(peak) peak on?resistance v is = gnd to v cc ; v i = v ih , see figure 2 i s = 4 ma 1.65 74.5 220 i s = 8 ma 2.3 20 75 i s = 24 ma 3.0 11.5 25 i s = 32 ma 4.5 7.5 17 r on on?resistance mismatch between switches v is = gnd to v cc ; v i = v ih , see figure 2 i s = 4 ma 1.65 8.0 i s = 8 ma 2.3 5.0 i s = 24 ma 3.0 3.0 i s = 32 ma 4.5 2.0 bw bandwidth (f ?3db ) r l = 50 , c l = 5 pf, f in = sine wave see figure 8 1.65 > 270 mhz 2.3 > 270 3.0 > 270 4.5 > 270
nlx2g66 www. onsemi.com 4 table 5. analog switch characteristics (continued) symbol parameter conditions v cc 25 c unit typ iso off off?channel feedthrough isolation r l = 600 , c l = 50 pf, f in = 1 mhz sine wave see figure 9 1.65 ?70 db 2.3 ?70 3.0 ?70 4.5 ?70 r l = 50 , c l = 5 pf, f in = 1 mhz sine wave see figure 9 1.65 ?60 2.3 ?60 3.0 ?60 4.5 ?60 xtalk crosstalk between switches r l = 600 , c l = 50 pf, f in = 1 mhz sine wave see figure 10 1.65 ?100 db 2.3 ?100 3.0 ?100 4.5 ?100 r l = 50 , c l = 5 pf, f in = 1 mhz sine wave see figure 10 1.65 ?90 2.3 ?90 3.0 ?90 4.5 ?90 feedthrough noise, control to switch r l = 600 , c l = 50 pf, f in = 1 mhz square wave, t r = t f = 2 ns, see figure 11 1.65 10 mv pp 2.3 10 3.0 10 4.5 15 thd total harmonic distortion c l = 50 pf, r l = 50 , f in = 600 hz to 20 khz sine wave, see figure 12 2.3 0.025 % 3.0 0.015 4.5 0.01 table 6. power dissipation characteristics symbol parameter conditions v cc 25 c unit typ c pd power dissipation capacitance f = 10 mhz 1.65 8.0 pf 2.3 8.9 3.0 9.6 4.5 10.9
nlx2g66 www. onsemi.com 5 table 7. device ordering information device order number package shipping ? nlx2g66dmutag udfn8?0.5p, 1.95 mm x 1.0 mm (pb?free) 3000 / tape & reel nlx2g66dmutcg udfn8?0.5p, 1.95 mm x 1.0 mm (pb?free) 3000 / tape & reel nlx2g66mu3tcg (in development) udfn8?0.35p, 1.45 mm x 1.0 mm (pb?free) 3000 / tape & reel NLX2G66FCTAG wlcsp8, 1.888 mm x 0.888 mm (pb?free) 3000 / tape & reel ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d.
nlx2g66 www. onsemi.com 6 figure 2. on resistance test set?up figure 3. maximum off?channel leakage current test set?up figure 4. maximum on?channel leakage current test set?up figure 5. propagation delay test set?up figure 6. propagation delay output enable/disable test set?up figure 7. power dissipation capacitance test set?up power supply computer dc parameter analyzer v cc + - plotter v cc v il v cc v cc a v cc v ih v cc a n/c v cc v cc test point v cc v cc v cc 2 1 2 1 r l c l * *includes all probe and jig capacitance. test point switch to position 2 when testing t plz and t pzl switch to position 1 when testing t phz and t pzh v cc n/c n/c a gnd v cc gnd v cc gnd v cc gnd v cc gnd v cc gnd v cc v ih
nlx2g66 www. onsemi.com 7 figure 8. maximum on?channel bandwidth test set?up figure 9. off?channel feedthrough isolation test set?up figure 10. crosstalk (between switches) figure 11. feedthrough noise, on/off control to analog out, test set?up v cc *includes all probe and jig capacitance. db meter 0.1 f v os f in v cc *includes all probe and jig capacitance. db meter 0.1 f v os f in r l v is v cc *includes all probe and jig capacitance. v os (v cc )/2 i s r l r l gnd v cc v in 1mhz t r t f 2ns gnd v cc gnd v cc gnd v cc
nlx2g66 www. onsemi.com 8 figure 12. total harmonic distortion test set?up figure 13. propagation delay, analog in to analog out waveforms figure 14. propagation delay, on/off control v cc *includes all probe and jig capacitance. 0.1 f v is f in v os to distortion meter (v cc )/2 r l v cc v oh 50% 50% v cc x a y a t phl t plh 50% v cc v ol v cc 10% 50% v cc control analog out t plz t pzl 50% v cc 50% v cc t phz t pzh v ol v oh high impedance high impedance 90% t r t f 90% 10% gnd v cc
nlx2g66 www. onsemi.com 9 package dimensions udfn8 1.45x1.0, 0.35p case 517bz issue o soldering footprint* recommended dim min max millimeters a 0.45 0.55 a1 0.00 0.05 a3 0.13 ref b 0.15 0.25 d 1.45 bsc e 1.00 bsc e 0.35 bsc l 0.25 0.35 l1 0.30 0.40 a b e d 0.10 c pin one reference top view 0.10 c a a1 0.05 c 0.05 c c seating plane side view 2x 2x a3 bottom view b e 8x l 7x l1 1 4 5 8 e/2 dimensions: millimeters 0.22 7x 0.48 8x 1.18 0.53 pitch 0.35 1 pkg outline 0.10 b 0.05 a c c note 3 m m
nlx2g66 www. onsemi.com 10 package dimensions udfn8 1.95x1.0, 0.5p case 517ca issue o soldering footprint* recommended dim min max millimeters a 0.45 0.55 a1 0.00 0.05 a3 0.13 ref b 0.15 0.25 d 1.95 bsc e 1.00 bsc e 0.50 bsc l 0.25 0.35 l1 0.30 0.40 a b e d 0.10 c pin one reference top view 0.10 c a a1 0.05 c 0.05 c c seating plane side view 2x 2x a3 bottom view b e 8x l 7x l1 1 4 5 8 e/2 dimensions: millimeters 0.30 7x 0.49 8x 1.24 0.54 pitch 0.50 1 pkg outline 0.10 b 0.05 a c c note 3 m m
nlx2g66 www. onsemi.com 11 package dimensions wlcsp8, 1.888x0.888 case 567mr issue o seating plane notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. coplanarity applies to spherical crowns of solder balls. dim a min max ??? millimeters a1 e 0.50 bsc b 0.21 0.25 0.50 e d a b pin a1 reference e a 0.15 b c 0.03 c 0.05 c 8x b 12 d c b a1 c 0.15 0.19 pitch 0.20 8x dimensions: millimeters *for additional information on our pb?free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* 0.50 0.50 top view side view bottom view note 3 recommended package outline e pitch a a e/2 e/2 d 1.858 1.918 e 0.858 0.918 a1 on semiconductor and the are registered trademarks of semiconductor components industries, llc (scillc) or its subsidia ries in the united states and/or other countries. scillc owns the rights to a number of pa tents, trademarks, copyrights, trade secret s, and other intellectual property. a listin g of scillc?s product/patent coverage may be accessed at www.onsemi.com/site/pdf/patent?marking.pdf. scillc reserves the right to make changes without further notice to any product s herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any part icular purpose, nor does sci llc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ?typi cal? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating param eters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the right s of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgic al implant into the body, or other applications intended to s upport or sustain life, or for any other application in which the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer s hall indemnify and hold scillc and its officers , employees, subsidiaries, affiliates, and dist ributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufac ture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. p ublication ordering information n. american technical support : 800?282?9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81?3?5817?1050 nlx2g66/d literature fulfillment : literature distribution center for on semiconductor 19521 e. 32nd pkwy, aurora, colorado 80011 usa phone : 303?675?2175 or 800?344?3860 toll free usa/canada fax : 303?675?2176 or 800?344?3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your loc al sales representative

▲Up To Search▲

Price & Availability of NLX2G66FCTAG

	To Download NLX2G66FCTAG Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .